sandwich panel erection anchor with shear plate
Full embedment, reinforcement and a minimum compressive
strength of 3,300 psi gives the 4 - 5 ton Sandwich Panel Erection
Anchor a pullout strength equal to their ultimate mechanical strength
if reinforced with 2 ea. #3 Rebar x 2’-6" bent on a 30° angle.
Full embedment, reinforcement and a minimum compressive
strength of 4,500 psi gives the 8-10 ton Sandwich Panel Erection
Anchor a pullout strength equal to their ultimate mechanical strength
if reinforced with 2 ea. #5 Rebar x 3’-6" bent on a 30° angle.
sandwich panel erection anchor with shear plate |
Part # Plain |
Part # galvanized |
anchor (Tons) |
Clutch id. |
anchor |
Plate |
weight (lbs.) |
box Qty |
a |
l |
b |
c |
d |
242-0431 |
242-0432 |
4T |
4-5T |
6" |
3-1/2" |
5/8" |
3/8" |
3" x 3" |
4.20 |
20 |
242-0531 |
242-0532 |
5T |
4-5T |
6" |
3-1/2" |
5/8" |
3/8" |
3" x 3" |
4.20 |
20 |
242-0831 |
242-0832 |
8T |
8-10T |
6" |
4-3/4" |
3/4" |
3/8" |
3" x 4" |
6.55 |
10 |
242-1031 |
242-1032 |
10T |
8-10T |
6" |
4-3/4" |
3/4" |
3/8" |
3" x 4" |
6.55 |
10 |
sandwich panel anchor
10" panel (3.5" x 2" x 3.5")
sandwich panel anchor |
anchor (tons) |
erection Shear(lbs.) |
tension (lbs.) |
4T |
5,500 |
8,000 |
5T |
5,500 |
10,000 |
8T |
6,500 |
16,000 |
10T |
6,500 |
20,000 |
ring lift clutch
The Ring Lift Clutch is designed with a curved interlocking clutch
body that rotates to lock over the protruding ring lift anchor.
ring lift clutch |
Part |
ring clutch (Tons) |
clutch id |
l |
b |
c |
d |
e |
weight (lbs.) |
239-0200 |
2T |
2-2.5T |
10-15/16" |
3-1/8" |
3-1/16" |
2-5/16" |
3-3/4" |
1 |
239-0400 |
4T |
4-5T |
12-15/16" |
4-1/16" |
3-7/8" |
2-7/16" |
4-9/16" |
9.25 |
239-0800 |
8T |
8-10T |
17-3/8" |
5-7/8" |
5-1/4" |
3-3/8" |
6-5/16" |
22.80 |
ring lift reusable recess former
The Ring Lift Reusable Recess Former are manufactured with a
durable urethane rubber to with stand many uses. The holding
plate fastens the recess former and anchor to the formwork by
either welding or bolting. The recess former is than attached by
sliding it over the two protruding pins on the mounting plate. This
allows for an accurate installation and quick assembly.
ring lift reusable recess former |
Part |
ringclutch(Tons) |
clutch id. |
length(L) |
height(D) |
width(E) |
slotWidth (A) |
hole Dist. (B) |
hole Dia. (C) |
weight lbs. |
290-0100 |
1T |
1-1.3T |
3-3/4" |
1-7/8" |
1-3/4" |
3/16" |
1-1/16" |
0.406" |
0.20 |
290-0200 |
2-2.5T |
2.5T |
3-3/4" |
1-7/8" |
1-3/4" |
3/8" |
1-1/16" |
0.406" |
0.20 |
290-0500 |
4-5T |
5T |
4-7/8" |
2-1/4" |
2-3/16" |
5/8" |
1-3/8" |
0.406" |
0.44 |
290-1000 |
8-10T |
10T |
ut lift anchor & recess former attachments
ut lift anchor with clip
The UT Anchor with Clip is designed to eliminate bolting the recess former to the framework. The specially designed clip allows the anchor to be attached to the framework without the need for any attachment hardware. The location of the clip decides the amount of pressure the former presses against the core for jacket of the form.
How to Order:
• Specify the UT Anchor to use
• Specify Clip Length (Dimension "L")
• Specify Offset (Dimension "0"), if none is specified clip to be centered
• Specify height from top (Dimension "T") or bottom (Dimension "B") of UT Anchor
• Specify Coating – Plain or Galvanized
• Specify quantity
cable loop anchor
The Cable Loop Anchor is an economical lifting system for a variety
of applications. The cable loop anchor can be either wet set or tied
off to the reinforcement steel prior to pouring with an embedment
of 2/3 of the length of the anchor.
No special lifting hardware is required, any hook or clevis
will be sufficient.
cable loop anchor |
Part # |
description (lbs.) |
SW |
h |
b |
c |
d |
tag color |
weight |
236-0080 |
0.8T Cable Loop Anchor |
1,600 |
8" |
3.75" |
0.236" |
5.30" |
White |
0.22 |
236-0120 |
1.2T Cable Loop Anchor |
2,400 |
9" |
4" |
0.276" |
6" |
Red |
0.29 |
236-0160 |
1.6T Cable Loop Anchor |
3,200 |
10" |
5" |
0.315" |
6.70" |
Purple |
0.40 |
236-0200 |
2.0T Cable Loop Anchor |
4,000 |
12" |
5.25" |
0.354" |
8" |
Green |
0.78 |
236-0250 |
2.5T Cable Loop Anchor |
5,000 |
13" |
5.50" |
0.394" |
8.70" |
Dark Gray |
0.97 |
236-0380 |
3.8 Cable Loop Anchor |
7,600 |
14.5" |
6.50" |
0.472" |
9.70" |
Yellow |
1.24 |
236-0500 |
5T Cable Loop Anchor |
10,000 |
15" |
7" |
0.551" |
10" |
Dark Blue |
1.6 |
236-0630 |
6.3T Cable Loop Anchor |
12,600 |
16.5" |
9.25" |
0.630" |
11" |
Light Blue |
1.89 |
236-0800 |
8T Cable Loop Anchor |
16,000 |
19" |
9.25" |
0.709" |
12.7" |
Light Gray |
2.14 |
236-0990 |
9.9T Cable Loop Anchor |
19,800 |
21" |
10.25" |
0.787" |
14" |
Pink |
2.64 |
236-1200 |
12T Cable Loop Anchor |
24,000 |
23" |
11" |
0.866" |
15.3" |
Black |
2.12 |
236-1600 |
16T Cable Loop Anchor |
32,000 |
26" |
12.75" |
1.024" |
17.3" |
Brown |
3.67 |
236-2500 |
25T Cable Loop Anchor |
50,000 |
33.5" |
15.75" |
1.260" |
22.3" |
Tan |
5.32 |
thin slab coil insert
The Thin Slab Coil Insert is designed for use in thin slab elements,
where a standard length inserts will not fit.
thin slab coil insert |
Part # Plain |
Part # galvanize |
bolt Dia. |
height (A) |
swl Tension (lbs.) |
Coil Dia. (E) |
Coil Length (B) |
wire Dia. (F) |
length (D) |
Min. Edge Distance |
weight (lbs.) |
box Qty |
197-0402 |
197-0412 |
1/2" |
1-3/4" |
950 |
1-1/4" |
1-1/8" |
.225" |
4-1/2" |
4" |
0.26 |
120 |
197-0602 |
197-0602 |
3/4" |
2-1/4" |
2,000 |
1-5/8" |
1-5/8" |
.306" |
5" |
5" |
0.56 |
N/A |
197-0604 |
197-0614 |
3/4" |
3-1/2" |
3,400 |
2" |
2" |
.306" |
6" |
6" |
0.67 |
50 |
197-0802 |
197-0812 |
1" |
2-5/16" |
2,000 |
2" |
2" |
.306" |
6" |
5" |
0.79 |
N/A |
197-0805 |
197-0815 |
1" |
4-1/2" |
4,750 |
2" |
2" |
.306" |
6" |
8" |
0.97 |
N/A |
straight coil loop insert
The Straight Coil Loop Insert is an efficient insert for lifting and
handling precast elements.
straight coil loop insert |
Part # plain |
Part # galvanized |
bolt Dia. |
length (L) |
width (W) |
thread (t) |
Coil Length (C) |
wire Dia. (D) |
SWL Tension |
weight |
194-10403 |
194-50403 |
1/2" |
3" |
1-5/16" |
1/2 - 6 |
1-3/16" |
.225" |
2,250 |
0.18 |
194-10404 |
194-50404 |
1/2" |
4" |
1-5/16" |
1/2 - 6 |
1-3/16" |
.225" |
2,250 |
0.18 |
194-20406 |
194-60406 |
1/2" |
6" |
1-3/8" |
1/2-6 |
1-3/16" |
.306" |
3,600 |
0.30 |
194-10604 |
194-50604 |
3/4" |
4" |
1-5/8" |
3/4 - 4.5 |
1-5/8" |
.306" |
3,750 |
0.38 |
194-20606 |
194-60606 |
3/4" |
6" |
1-7/8" |
3/4 - 4.5 |
1-5/8" |
.375" |
4,500 |
0.39 |
194-10804 |
194-50804 |
1" |
4" |
2-1/16" |
1 - 3.5 |
2" |
.375" |
3,750 |
0.84 |
194-10804-32 |
194-50804-32 |
1" |
4-1/2" |
2-1/16" |
1 - 3.5 |
2" |
.375" |
3,750 |
0.87 |
194-10805 |
194-50805 |
1" |
5" |
2-1/16" |
1 - 3.5 |
2" |
.375" |
3,750 |
0.92 |
194-10806 |
194-50806 |
1" |
6" |
2-1/16" |
1 - 3.5 |
2" |
.375" |
4,500 |
0.97 |
194-10808 |
194-50805 |
1" |
8" |
2-1/16" |
1 - 3.5 |
2" |
.375" |
4,500 |
1.30 |
194-10810 |
194-51008 |
1-1/4" |
8" |
2-1/2" |
1-1/4 - 3.5 |
2-1/2" |
.440" |
5,500 |
1.80 |
single flared coil loop insert
The Single Flared Coil Loop Insert design allows for a higher
load capacity than the straight coil insert, due to it’s flared loop
configuration.
single flared coil loop insert |
Part # plain |
Part # galvanized |
bolt Dia. |
length (A) |
Coil Length (B) |
Coil Width (C) |
wire Dia. (D) |
weight (E) |
swl Tension (lbs.) |
weight (lbs.) |
box Qty |
198-10606 |
198-50606 |
3/4" |
6" |
1-3/4" |
1-3/4" |
.375" |
3-1/2" |
4,750 |
0.60 |
80 |
198-10609 |
198-50609 |
3/4" |
9" |
1-3/4" |
1-3/4" |
.375" |
5-1/2" |
4,750 |
0.79 |
80 |
198-10803 |
198-50809 |
1" |
9" |
2-1/16" |
2" |
.375" |
5-1/2" |
4,750 |
1.20 |
50 |
198-20812 |
198-60809 |
1" |
9" |
2-1/16" |
2-1/2" |
.440" |
5-3/4" |
8,000 |
1.80 |
30 |
198-10812 |
198-50812 |
1" |
12" |
2-1/16" |
2" |
.375" |
5-1/2" |
4,750 |
1.52 |
30 |
198-20812 |
198-60812 |
1" |
12" |
2-1/16" |
2-1/2" |
.440" |
5-3/4" |
8,000 |
1.77 |
30 |
198-11012 |
198-61012 |
1-1/4" |
12" |
2-5/16 |
2-1/2" |
.375" |
5-3/4" |
4,750 |
1.50 |
30 |
198-21012 |
198-61012 |
1-1/4" |
12" |
2-5/16 |
2-1/2" |
.440" |
5-3/4" |
8,000 |
1.85 |
30 |
198-11212 |
198-61212 |
1-1/2" |
12" |
2-5/16 |
2-3/4" |
.440" |
5-3/4" |
8,000 |
2.05 |
25 |
criss cross double flared coil loop insert
The Criss Cross Double Flared Coil Loop Insert design allows for a
higher load capacity than the single flared coil loop insert, due to its
criss cross double flared loop configuration.
criss cross double flared coil loop insert |
Part # plain |
Part # galvanized |
bolt Dia. |
insert length (L) |
Coil Dia. (B) |
Coil Length (E) |
wire Dia. (D) |
loop Dia. (W) |
swl Tension (lbs.) |
weight (lbs.) |
199-10812 |
199-50812 |
1" |
12-3/8" |
2-1/16" |
2-1/16" |
.375" |
5-1/2" |
9,500 |
2.40 |
199-20812 |
199-60812 |
1" |
12-1/2" |
2-1/4" |
2-1/16" |
.440" |
5-3/4" |
13,500 |
3.10 |
199-11012 |
199-51012 |
1-1/4" |
12-3/8" |
2-5/16" |
2-1/16" |
.375" |
5-3/4" |
9,500 |
2.50 |
199-21012 |
199-61012 |
1-1/4" |
12-1/2" |
2-1/2" |
2-1/16" |
.440" |
5-3/4" |
13,500 |
3.20 |
199-11212 |
199-51212 |
1-1/2" |
12-3/8" |
2-9/16" |
2-3/8" |
.375" |
5-3/4" |
9,500 |
2.70 |
199-21212 |
199-61212 |
1-1/2" |
12-1/2" |
2-3/4" |
2-3/8" |
.440" |
5-3/4" |
13,500 |
3.40 |
double flared coil loop insert
The Double Flared Coil Loop Insert design allows for a higher load
capacity than the single flared coil loop insert, due to it’s double
flared loop configuration.
double flared coil loop insert |
Part # plain |
Part # galvanized |
bolt Dia. |
insert length (L) |
Coil Dia. (A) |
Coil Length (B) |
wire Dia. (D) |
loop Dia. (W) |
swl Tension (lbs.) |
weight (lbs.) |
188-10812 |
188 -50812 |
1" |
12" |
2-1/16" |
2-1/16" |
.375" |
5-1/2" |
9,500 |
2.40 |
188-20812 |
188-60812 |
1" |
12" |
2-1/4" |
2-1/16" |
.440" |
5-3/4" |
13,500 |
3.10 |
188-11012 |
188-51012 |
1-1/4" |
12" |
2-5/16" |
2-1/16" |
.375" |
5-3/4" |
9,500 |
2.50 |
188-21012 |
188-61012 |
1-1/4" |
12" |
2-1/2" |
2-1/16" |
.440" |
5-3/4" |
13,500 |
3.20 |
188-11212 |
188-51212 |
1-1/2" |
12" |
2-9/16" |
2-3/8" |
.375" |
5-3/4" |
9,500 |
2.70 |
188-21212 |
188-61212 |
1-1/2" |
12" |
2-3/4" |
2-3/8" |
.440" |
5-3/4" |
13,500 |
3.40 |
"L" Leg coil insert
The Double Flared Coil Loop Insert four leg design makes it an ideal
insert for thin slab applications.
"L" Leg coil insert |
Part # plain |
Part # galvanized |
bolt Dia. |
insert length (L) |
Coil Length (A) |
Coil length (B) |
wire Dia. (D) |
leg Length (W) |
swl Tension (lbs.) |
weight (lbs.) |
195-0603 |
195-0613 |
3/4" |
3" |
1-3/4" |
1-5/8" |
.306" |
7-1/8" |
2,500 |
0.70 |
195-0804 |
195-0814 |
1" |
4" |
2-1/16" |
1-7/8" |
.306" |
9-1/2" |
3,500 |
1.00 |
195-1004 |
195-1014 |
1-1/4" |
4" |
2-1/16" |
2-1/4" |
.375" |
9-3/4" |
4,000 |
1.20 |
195-1204 |
195-1214 |
1-1/2" |
4" |
2-1/16" |
2-1/2" |
.375" |
10" |
4,000 |
1.40 |
open coil insert
The Open Coil Insert has a unique open coil design to enlarge the
shear cone, which increases the load capacity.
open coil insert |
Part # plain |
Part # galvanized |
bolt Dia. |
insert length (L) |
safe Working Load |
no. Struts |
wire Dia. (D) |
Coil Width (W) |
open Coil Length (B) (lbs.) |
weight |
tension |
shear |
196-0600 |
196-0610 |
3/4" |
4-1/2" |
4,250 |
4,250 |
2 |
.375" |
2-1/8" |
1-1/2" |
0.55 |
196-0800 |
196-0810 |
1" |
5-1/2" |
6,250 |
6,250 |
2 |
.440" |
2-1/2" |
2-1/4" |
1.12 |
196-0830 |
196-0840 |
1" |
7-1/2" |
10,000 |
12,000 |
4 |
.440" |
2-3/4" |
2-3/4" |
2.15 |
196-1030 |
196-1040 |
1-1/4" |
7-1/2" |
12,000 |
12,000 |
4 |
.440" |
3" |
2-3/4" |
3.90 |
2-strut coil tie
The 2-Strut Coil Tie is an effective way to lift and handle your thin
wall concrete element.
2-strut coil tie |
Part # plain |
Part # galvanize |
bolt Dia. |
insertLength (L) |
Coil Length (A) |
Coil Width (W) |
wire Dia. (D) |
swl Tension |
edge Dist. |
weight (lbs.) |
192-2206006 |
192-2206106 |
3/4" |
6" |
1-3/4" |
1-5/8" |
.375" |
4,500 |
8" |
0.91 |
192-2108008 |
192-2108108 |
1" |
8" |
2-1/16" |
2-1/4" |
.440" |
6,000 |
8" |
1.55 |
192-2110010 |
192-2110110 |
1-1/4" |
10" |
2-1/16" |
2-1/2" |
.440" |
6,750 |
10" |
1.93 |
4-strut coil tie
The 4-Strut Coil Tie can develop high capacities by varying the wire
and coild diameter. These inserts are ideal for lifting and handling
precast concrete elements.
4-strut coil tie |
Part plain |
Part galvanize |
bolt Dia. in. |
insertLength (L) in. |
CoilLength(A) in. |
CoilWidth(W) in. |
wire Dia.(D) in. |
swlTension in. |
edgeDist. in. |
weight (lbs.) |
192-4108008 |
192-4108108 |
1 |
8 |
2-1/16 |
2-1/16 |
.375" |
9,000 |
10 |
1.42 |
192-4108012 |
192-41081128 |
1 |
12 |
2-1/16 |
2-1/4 |
.375" |
9,000 |
15 |
1.67 |
192-4110008 |
192-4110108 |
1-1/4 |
8 |
2-1/16 |
2-1/2 |
.440 |
9,000 |
10 |
2.25 |
192-4110012 |
192-4110112 |
1-1/4 |
12 |
2-1/16 |
2-1/2 |
.440 |
13,500 |
15 |
2.75 |
coil threaded cable lifting loop
The 4-Strut Coil Tie can develop high capacities by varying the wire
and coild diameter. These inserts are ideal for lifting and handling
precast concrete elements.
coil threaded cable lifting loop |
Part # |
bolt Dia. (D) |
insert Length (L) |
Collar Length (A) |
thread Length (B) |
SWL Tension |
weight (lbs.) |
190-1516 |
1/2" |
10" |
2-1/2" |
1-3/4" |
1,100 |
0.19 |
190-1524 |
3/4" |
10" |
2-1/2" |
1-3/4" |
4,600 |
0.25 |
190-1532 |
1" |
13" |
3" |
2-1/4" |
8,000 |
0.43 |